Description:
|
adsl2SCStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2SCStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2SCStatusTable contains status parameters
of ADSL2 sub-carriers. This following points apply to this
table :
1. The main purpose of this table is to hold the results
of a DELT test.
2. This table also holds parameters obtained at line
initialisation time.
3. The rows in this table are volatile, that is they are
lost if the SNMP agent is rebooted.
4. Due to the large OCTET STRING attributes in this table,
the worst case memory requirements for this table are
very high. The manager may use the row status attribute
of this table to delete rows in order to reclaim memory.
5. The manager may create rows in this table. The SNMP
agent may create rows in this table. Only the manager
may delete rows in this table.
6. The maximum number of rows allowable in this table is
indicated by the scalar attribute
adsl2ScalarSCMaxInterfaces.
The number of rows available in this table is indicated
by the scalar attribute adsl2ScalarSCAvailInterfaces.
7. The SNMP agent is permitted to create rows in this table
when a DELT test completes successfully or when line
initialisation occurs. It is not mandatory for the SNMP
agent to create rows in this table, hence it may be
necessary for the manager to create rows in this table
before any results can be stored.
8. If the manager attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail and the response to the SNMP SET PDU
will contain the error noCreation(11).
9. If the SNMP agent attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail and the attribute
adsl2LineCmndConfLdsfFailReason will indicate the
reason for the failure. The failure reason will be either
tableFull(10) or noResources(11).
10. An example of use of this table is as follows :
Step 1. : The DELT test is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT test completes and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : Due to a low memory condition, a row in the
: adsl2SCStatusTable table cannot be created at
: this time.
Step 5. : The reason for the failure, tableFull(10), is
: indicated in the adsl2LineCmndConfLdsfFailReason
: attribute.
11. Another example of use of this table is as follows :
Step 1. : The DELT test is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT test completes and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : The row creation is successfully.
Step 5. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2).
12. Another example of use of this table is as follows :
Step 1. : The manager creates a row in adsl2SCStatusTable
: for a particular ADSL2 line.
Step 2. : The DELT test is started on the above mentioned
: line by setting the adsl2LineCmndConfLdsf from
: inhibit to force.
Step 3. : The DELT test completes and valid data is
: available.
Step 4. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2)."
|
|
iso(1)
adsl2SCStatusEntry(1) 
