---
oid: "1.3.6.1.4.1.119.2.3.14.9.4.5"
asn1-notation: "{iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) 119 nec-mib(2) necProductDepend(3) atomis-mib(14) m7-phase2-mib(9) conn(4) connSoftPvcTable(5)}"
description: "connSoftPvcTable OBJECT-TYPE"
classification: "MIB object for network management"
last-modified: "2020-11-18"
---

## OID : `1.3.6.1.4.1.119.2.3.14.9.4.5`

```asn1
{iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) 119 nec-mib(2) necProductDepend(3) atomis-mib(14) m7-phase2-mib(9) conn(4) connSoftPvcTable(5)}
```

### Description

```asn1
connSoftPvcTable OBJECT-TYPE
SYNTAX SEQUENCE OF ConnSoftPvcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table include all entries to Soft-PVPC/PVCC
currently available between the lines or the line and
CPU port of the switch. Also, this table is used to
set or delete Soft-PVPC/PVCC. The operable
connection form between Soft-PVPC/PVCC is bi-
directional point-to-point only.
The procedure to set the connection is as follows:
1. Acquire connSoftPvcIndex
To set the connection, read connSoftPvcIndexNext and
obtain an index of the Soft-PVPC/PVCC table. The
index must be managed by NMS. (The index is required
to take an action to the connection.)
2. Set createAndWait
Set connSoftPvcRowStatus to CreateAndWait, using the
obtained connSoftPvcIndex as index. If the agent
will set the parameter for the Soft-PVPC/PVCC
setting to the default value and make
connSoftRowStatus to notReady.
However, the same manager cannot create another row
while creating a row (the status of the row is notRedy
or notInService).
3. Get the default value
Get the default value of the object which serves as
parameter for the connection setting. (The agent
shall return -1 if it does not have a default value.)
Default values are as follows:
connSoftPvcTopology bi-directional-VCC(2)
connSoftPvcTrafficType traffic-UBR(5)
connSoftPvcEndpointType calling(1)
connSoftPvcRetry 2
connSoftPvcSrcAtmAddressFormat nsap(2)
connSoftPvcSrcAtmAddressLength None
connSoftPvcSrcAtmAddress 0 length string
connSoftPvcSrcIfIndex None
connSoftPvcSrcVPI None
connSoftPvcSrcVCI None
connSoftPvcDstAtmAddressFormat nsap(2)
connSoftPvcDstAtmAddressLength None
connSoftPvcDstAtmAddress 0 length string
connSoftPvcDstIfIndex None
connSoftPvcDstVPI None
connSoftPvcDstVCI None
connSoftPvcSrcFifoIndex 0
connSoftPvcDstFifoIndex 0
connSoftPvcNodeKind model5(1)
connSoftPvcSrcParam1 off(1)
connSoftPvcDstParam1 off(1)
connSoftPvcSrcParam2 0 length string
connSoftPvcDstParam2 0 length string
connSoftPvcSrcParam3 -1
connSoftPvcDstParam3 -1
connSoftPvcSrcParam4 -1
connSoftPvcDstParam4 -1
connSoftPvcSrcParam5 -1
connSoftPvcDstParam5 -1
connSoftPvcSrcParam6 off(2)
connSoftPvcDstParam6 off(2)
connSoftPvcSrcParam7 None (not installed)
connSoftPvcDstParam7 None (not installed)
4. Set parameter
If a parameter does not have a default value, or the
default value should not be used, set the parameter to
a value.
If all parameters are set, the agent shall make
connSoftPvcRowStatus to notInService.
5. Set active
By doing so, the agent checks parameters, resources and
establishes the connection.
6. Get connSoftPvcRowStatus
If connSoftPvcRowStatus is active, the connection
setting completed successfully, if notInService,the
connection setting failed. For the cause, refer to
connSoftPvcCause.
(Note) When the connection setting has failed, if the
connection is not released, the row will remain.
7. Get connSoftPvcRestRetry
Remaining counts of retry are contained. If it is
positive value, the retry is in progress. If
connSoftPvcRestRetry is 0, the retry completed. The
result of the connection setting should be seen, when
this object is 0.
-1 means that infinite retry is in progress.
***Special pattern***
(1) If connSoftPvcTopology is bi-directional-VPC, set
connSoftPvcSrcVCI, connSoftPvcDstVCI to 0.
The procedure to release the connection is as follows:
1. Set 'destroy'
Set connSoftPvcRowStatus to 'destroy', using
connSoftPvcIndex of the connection to be deleted as
index.
The agent will delete the connection, referring to
it.
(Note) 'destroy' can also be set during the bypass
processing.
2. Get the result
If the connection is deleted, 'get' of
connSoftPvcTable of the designated index becomes
NoSuchName.
The bypass processing of connection
1. Set notInService
When the agent executes the bypass processing of
connection, set connSoftPvcRowStatus to
notInService, and then establish the connection.
2. Get connSoftPvcRowStatus
If connSoftPvcRowStatus is 'active', the bypass
connection setting has completed successfully.
If connSoftPvcRowStatus remains 'notInService',
the connection setting has failed.
Others
1. The cut and recovery processing of connection is
performed, following the delete and set procedures
of the concerned connection.
Each procedure is as stated before."
```

**Classification**: MIB object for network management

### Child OIDs

- [OID `1.3.6.1.4.1.119.2.3.14.9.4.5.1`](https://oid-base.com/get-md/1.3.6.1.4.1.119.2.3.14.9.4.5.1): `connSoftPvcEntry(1)`

### Terms of Use
[Terms of use](https://oid-base.com/disclaimer.htm.md)
